|
ttmax
Harley Benton Expert
|
Post by ttmax on Mar 26, 2020 21:42:20 GMT
Now pos 1 kb 10 bridge output max neck min (*) pos 1 kb 0 bridge + neck output max pos 2 kb 10 bridge+midle output max neck min (*) pos 2 kb 0 bridge+midle+neck output max pos 3 kb 0/10 only middle Pos 4 kb 10 neck+midle output max bridge min (*) pos 4 kb 0 neck+midle+bridge output max pos 5 kb 10 neck output max bridge min (*) Pos 5 kb 0 neck + bridge output max (*) Little toc audible knock on with metal obhect
|
|
|
ttmax
Harley Benton Expert
|
Post by ttmax on Mar 26, 2020 23:29:28 GMT
Thx, do you use generic tone pot or different pot Finally your wire is the same? I have the same of you but with differences Pos 1 and pos 5 with pot Blender 1 have always a little neck / bridge (i have the default hb pots)
|
|
|
|
ttmax
Harley Benton Expert
|
Post by ttmax on Mar 27, 2020 16:57:43 GMT
I don't THINK I get any bleed through of the other pickup in positions 1 and 5. Not noticeably so if I tap them with a screwdriver. Yes just kept the generic pot. Wiring I'm not sure which scheme I used. Hi, in your wire Blender potere have gnd or you remove on this only pot ? Do have used always a hb st-62 ? Your blender pot is log or Linear is 250k ? I dont found the problem. Blender work but when pot is on 10 do Not esclude completly pick-up that is used to blend On a fender i have used like this (CTS don't remember other make in the early 2005) www.mojotone.com/guitar-parts/Guitar-Potentiometers?search=Mojotone+CTS+250K+Blender+Potentiometer#.UOTYGGw0WSoAnd work right. The only differences are that i blend bridge + neck in pos 1 Nec+mid+bridge in pos 2 Mid+neck in pos 3 Mid+neck in pos 4 Neck in pos 5 And pot have also zero point after 10 I don't Know yet if using a STD tone pot like this Is mounted on hb st-62 is normal that second pick-up is however to min and never is exclude completly
|
|
|
|
|
|
|
|
|
ttmax
Harley Benton Expert
|
Post by ttmax on Mar 29, 2020 11:09:48 GMT
I'd imagine a dedicated 'blender pot' is a no load pot when fully on at 10. This presumably eliminates this small amount of bleeding that is annoying you. Probable, I just have to find a place to buy it, to take it to the USA it costs me more the shipping than the pot or the kit and then I have to add the duties that are paid on the total not on the goods. However mod work i feel tone sound change if power on Blender, Honestly, only if I hit the screwdriver on the pickups do I feel a small toc on some as if it were active, but much lighter than the toc than when it is really active. I don't know if this depends on the quality of the pot / switches used by hb, on some false welding or on the fact that a dedicated blender pot must be used. for now I have used that of a tone and I do not even know if it is an A250k or a B250k so it could also depend on that, maybe you do not hear anything beating with the screwdriver on the pickups that should be off because you have a 500k I have not really idea I have to try on a pickguard to redo everything without mounting it on the guitar maybe so I resolve in the meantime out of laziness I leave it like this My old CTS pot (this have anche off position after 10 as a switch) used on old fender have stamp on this but don't found referendum to but a new one
|
|